Comments on: New CCNA – Operation Questions

By: R

Fri, 29 May 2015 13:07:32 +0000

@joseph

Hi! I will try my best to answer based from my understanding.

For Q10, The default gateway for the host should be the IP address of the router. Hence, default gateway for host A is 192.168.178 while the default gateway for host B is 192.168.1.130.

By: joseph

joseph — Tue, 26 May 2015 21:44:07 +0000

can someone please explain e why in question 10, we did not choose answer E, which gives you a fault gateway for host B at 192.18.1.129. If you look at the router configuration, it belongs in the same subnet as the IP address configured for the interface f0/0.20 . In other words, why did they choose a default gateway for host A, over host B?

By: Pascal

Pascal — Thu, 14 May 2015 16:24:42 +0000

IN Q7, the first 2 bytes should be 02 instead of 00 (inversion of the 7th bit from the original MAC address to become an IPv6 address), no ?

That’swhat your write but your scheme is then wrong.

By: kaka

kaka — Tue, 12 May 2015 08:35:19 +0000

@NK as you can note from the diagram host B is in vlan 2 and host A in Vlan 1 so the ip address and the default gateaway of host b must change to 10.1.2.254 and the ip address to 10.1.2.2. to enable frames to move

By: NK

NK — Sun, 10 May 2015 15:28:39 +0000

Can someone explain Q 6 for me?

I don’t understand it.

By: Hookah

Hookah — Thu, 07 May 2015 00:23:25 +0000

Question 8 still wonky on exam. Why would Router C send a Router Selection message type?

By: davesupreme

davesupreme — Mon, 04 May 2015 20:41:18 +0000

answers on Q8 test link wonky? only marked 2 correct
, supposed to be 3 correct answers?…. no problem, just wondering why?….

By: davesupreme

davesupreme — Mon, 04 May 2015 20:23:44 +0000

i saw that one too, Davy….

By: Nadith

Nadith — Sun, 03 May 2015 10:16:16 +0000

why Q4 B,C,E wrong ..can someone explain plz..??

By: Davy

Davy — Mon, 20 Apr 2015 13:52:13 +0000

Explenation for question 9 has some missing info:

When inverting the 7th bit which is 00 = 0000 0000 before we inverted is, and gets 0000 0010 = decimal number 2

So the new EUI-64 MAC is 02-12-34-FF-FE-56-78-9A instead of 00-12-34-FF-FE-56-78-9A (which was the MAC before inverting the 7th bit)

By: I have an exam

I have an exam — Sun, 05 Apr 2015 09:50:05 +0000

Which one is better, Academic exam or Professional exam?

By: ciscogeek

ciscogeek — Fri, 03 Apr 2015 19:16:58 +0000

Red, for Q10, E is incorrect because the default gateway for Host B -> port 9 -> vlan 20 is 192.168.1.130 (as shown in the diagram).

By: Peter

Peter — Thu, 26 Mar 2015 15:17:10 +0000

By: Apush

Apush — Wed, 18 Mar 2015 12:11:16 +0000

Passed my CCNA exam today (18th Mar)… Q2 in exam

By: Red

Red — Tue, 17 Mar 2015 14:47:15 +0000

I meant E and F can be the correct answers.

By: Red

Red — Tue, 17 Mar 2015 14:45:02 +0000

For Q 10, C and F are correct answers I think.

The address range is: 192.168.1.128 to 192.168.1.191

That means anything from and including 192.168.1.129 to 192.168.1.190 can be assigned to any interface, this including a pc or a default gateway.

By: mikael

mikael — Tue, 17 Mar 2015 14:20:57 +0000

Question 2, the link test is asking for 3 answers but when we fill 3 answers, the feedback is a fault answer even if we are right…..Link test doesn’t work for this question “Which three statements correctly describe Network Device A? (Choose three)”

By: muni

muni — Tue, 10 Mar 2015 12:40:58 +0000

Can anyone tell me, does final exam contain only questions and sims that I can find here, or it has an adittional lab simulation, that we have to set up by our own, just like we did after each term on academy.

Thanks

By: Anonymous

Anonymous — Thu, 05 Mar 2015 08:50:48 +0000

Host A IP address 192.168.1.64 is not correct because it’s the network address for VLAN 10.

By: bkool

bkool — Wed, 04 Mar 2015 03:50:57 +0000

Thanks Mubeen

By: Mubeen

Mubeen — Tue, 03 Mar 2015 23:56:55 +0000

@bkool
host A IP address: 192.168.1.64 cannot be correct because Host A is in VLAN 10, and for that (according to exhibit) starting IP is 192.168.1.78

By: bkool

bkool — Tue, 03 Mar 2015 19:08:14 +0000

Please 9tut, could you check this issue:
A. New CCNA – Operation Questions
Question 10
Refer to the exhibit:
A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three)
A. host A IP address: 192.168.1.79 **
B. host A IP address: 192.168.1.64
C. host A default gateway: 192.168.1.78
D. host B IP address: 192.168.1.128
E. host B default gateway: 192.168.1.129
F. host B IP address: 192.168.1.190
Answer: A C F
——————————————————————–
B. Composite Quiz 11
Question 23, same question:A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three)
Answers:
host A default gateway: 192.168.1.78
host B IP address: 192.168.1.190
host A IP address: 192.168.1.64 ( Answer different)**
Thanks to clarify

By: w1zard

w1zard — Mon, 02 Mar 2015 13:08:22 +0000

Question 3:
What is a “Cisco VPN solution”
What kind of “increased security” can be achieved over a VPN that is not achievable on a point-to-point WAN link such as a leased line?
Does this question appear in tests anymore? or is it a left-over from earlier exams?

By: M@x

M@x — Sun, 01 Mar 2015 09:42:51 +0000

CCNA20%India scheme works giving exam on 3rd march from mumbai
Total cost – $295
Discount – 20% = $295-$59 = $236
Payment made by credit card/debit card = Rs. 15200 (including taxes)

By: Anonymous

Anonymous — Sat, 28 Feb 2015 03:09:41 +0000

Correction:

For 192.168.1.130 /26 the useable addresses are: 192.168.1.128 – .190

By: Anonymous

Anonymous — Sat, 28 Feb 2015 03:08:26 +0000

Q10 Explanation:

It’s a “router-on-a-stick” configuration. Which means each host in the VLAN must corresponds with the VLAN configured on the sub-interfaces.
VLAN 10 is configured on fa0/0.10 and VLAN 20 on fa0/0.20. So each hosts in VLAN 10 must use fa0/0.10 IP address as their default gateway, each hosts must also be in the same subnet as fa0/0.10 IP – same with hosts in VLAN 20.

So find out the usable IP addresses on each sub-interfaces – for 192.168.1.78 /27: 192.168.1.65 – .94 and for 192.168.1.130 /26: 192.168.1.131 – .190
Host A (using port 6 – VLAN 10) must use IP 192.168.1.79, default gateway 192.168.1.78
Host B (using port 9 – VLAN 20) must use IP 192.168.1.190, default gateway 192.168.1.130

By: anybody

anybody — Tue, 24 Feb 2015 23:48:00 +0000

q10 – you have to look at router configuration to deduce what ip address can be used on which vlan and assigned to which host. Since host A is in vlan 10 he can have .79 ip and his default gateway has to be .78. Host B has to have .190 since he is in Vlan 20 and that subnet host’s are from 129-191.

By: modest

modest — Tue, 24 Feb 2015 11:24:47 +0000

9tut or anybody that how question 10, could u pls explain it to me. thanks in advance

By: Ronaldo

Ronaldo — Tue, 17 Feb 2015 04:41:55 +0000

Anyone from Mumbai,India ? Has anyone used CCNA20%India scheme on the exam vouchers ?
What’s the examination fee in Mumbai ? I’ll be appearing in 2nd week of March,2015.
Thank you!

By: CCNA

CCNA — Mon, 16 Feb 2015 07:58:17 +0000

Q2 was for 14th Feb Exam.

By: Che

Che — Mon, 16 Feb 2015 05:35:20 +0000

Q4, Q9 On 15th Feb.

By: Anonymous

Anonymous — Thu, 05 Feb 2015 14:02:08 +0000

@9tut

Question 2 in the Quizz is fault.
Answwrs are : Answer: B D E
Answer E is forgotten in the quiz.

Still Faulty !

By: Yannick

Yannick — Fri, 30 Jan 2015 16:40:34 +0000

Question 2 in the Quizz is fault.
Answwrs are : Answer: B D E
Answer E is forgotten in the quizz.

By: chinonso

chinonso — Tue, 27 Jan 2015 19:08:00 +0000

can anyone help me with latest dump on 200-120.
am preparing to write ma exams on first week of feb.

email id: sansalvado4queen@gmail.com

will highly appreciate u.
thnx.

By: murad

murad — Mon, 19 Jan 2015 20:12:57 +0000

Q2 & q6 in my exam today

By: agy

agy — Fri, 19 Dec 2014 21:47:27 +0000

q4 today

By: agy

agy — Fri, 19 Dec 2014 21:46:50 +0000

q2 today

By: Some dude

Some dude — Sat, 06 Dec 2014 03:58:18 +0000

@9tut quiz and answers here dont match. on some questions

By: sadk

sadk — Thu, 27 Nov 2014 14:16:15 +0000

Asnka please send me the dump that you did for pass the CCNA. kavinda_lakshitha@yahoo.com

By: Asanka11

Asanka11 — Tue, 25 Nov 2014 18:08:41 +0000

On 24th-Nov-2014 I Passed The CCNA 200 120 exam with 993. most of questions from 9tut.

I have my VCE simulations with the VCE player. asanka11@gmail.com

but nothing more 9tut is more than enough. do not waste your time with any site. follow 9tut.
Thank you very much 9tut.

By: richard

richard — Tue, 18 Nov 2014 15:12:46 +0000

subnet 255.255.255.128 cannot differentiate the two IP

By: richard

richard — Tue, 18 Nov 2014 15:11:49 +0000

IN Q2, why the answer is

B. With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.

D. With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.

By: Praveen

Praveen — Mon, 17 Nov 2014 16:57:14 +0000

@Jordan – E is wrong..Host B belongs to vlan20 and its default gateway is 192.168.1.130.It can be seen in the configuration

By: Jordan

Jordan — Sat, 15 Nov 2014 11:18:40 +0000

Hello,

Question 10, the correct answer are: A,E and F.

The network for vlan 10 is: 192.168.1.64/27
The network for vlan 20 is: 192.168.1.128/26

My email for questions is: jordan.rojasgarcia@gmail.com

By: Anonymous

Anonymous — Thu, 13 Nov 2014 08:42:24 +0000

Please what are Two enhancements that OSPFv3 supports over OSPFv2

By: kam

kam — Thu, 06 Nov 2014 21:06:42 +0000

q1,q10 on exam today

By: muhammad sabeeh haider

muhammad sabeeh haider — Mon, 03 Nov 2014 05:27:38 +0000

hye friends i have latest dumps exam no 200-120 i download by actual test.com if any one interested its cost 1000 rupee only.my gmail i.d sabeehhaider14@gmail.com

By: Dany

Dany — Wed, 29 Oct 2014 22:28:16 +0000

question 1 & 10 on exam today

By: Anonymous

Anonymous — Thu, 16 Oct 2014 11:00:43 +0000

Can anyone send me latest CCNA dumps??
Mail Id: Arya.ckd@gmail.com

By: skul

skul — Sat, 11 Oct 2014 18:28:47 +0000

Thanks 9tut.

There is no need to go for any dump or VCE just read and understand all the question of this site one time.
Best of luck

By: Idiocracy

Idiocracy — Wed, 01 Oct 2014 07:09:41 +0000

@ithory – EIGRP is an Advanced Distance Vector Protocol

By: ithory

ithory — Wed, 17 Sep 2014 17:27:24 +0000

EIGRP is not a distance vector protocol, is a hybrid protocol. Think about RIP in these questions.

By: Andres

Andres — Tue, 16 Sep 2014 19:09:45 +0000

I have a doubt about q4.
EIGRP dosn’t send periodic updates, so, why answer A is ok?
Thanks for your answers

By: sandipan

sandipan — Thu, 04 Sep 2014 21:19:47 +0000

can anyone tell me why 9tut is so popular

By: Ladjel

Ladjel — Sun, 31 Aug 2014 08:29:49 +0000

Question10:
VLAN10: 192.168.1.78 (010 0 1110)/27 ==> Net: 192.168.1.64/27 ; start: 192.168.1.65 (0100 0001) –> end:192.168.1.95(010 1 1111)
VLAN20: 192.168.1.130(10 00 0010)/26 ==> Net: 192.168.1.128/26; start: 192.168.1.129(10 00 0001)–> end:192.168.1.191(10 11 1111)

By: Menu

Menu — Thu, 28 Aug 2014 03:34:17 +0000

” Unlike RIP, EIGRP does not send periodic updates and route entries do not age out.”

By: Menu

Menu — Thu, 28 Aug 2014 03:30:42 +0000

Question 4:
What two things will a router do when running a distance vector routing protocol? (Choose two)

The answer(s) of A & D are given, but, as there are 2 common Distance Vector protocols in CCNA, RIP and EIGRP – EIGRP DOES NOT send periodic updates – this is taken straight from my CCNA handbook, Book3 Chapter 7. Theres trick questions, but hell this is wrong!

By: Helen

Helen — Tue, 12 Aug 2014 07:23:58 +0000

I just passed the ccna operation exam and now i start preparing my nest exam ccna data center through ccnapass4sure.com. All above questions are in my exam mostly Q10…
http://www.slideshare.net/cacciblansa/ccna-data-center-dumps

By: Strange

Strange — Wed, 16 Jul 2014 15:46:30 +0000

Question 5 was in the exam recently

By: Confused !

Confused ! — Tue, 08 Jul 2014 11:50:43 +0000

Q1,10 were in the today exam

By: An

An — Sat, 28 Jun 2014 18:06:56 +0000

Fa0/0.2 is at vlan 2 with the IP:10.1.2.254/24
that means that the PC B which is in the same vlan must be in the same network 10.1.2.0/24

thats why we must change the ip from 10.1.1.12(that belong to the network 10.1.1.0/24) to 10.1.2.2

By: Anonymous

Anonymous — Tue, 17 Jun 2014 23:08:47 +0000

can someone please explain why answer “D” is correct on question 6

By: Premium Member

Premium Member — Wed, 11 Jun 2014 18:31:02 +0000

The Premium Member question (randomized number) that corresponds to the the New CCNA – Operation Questions #2 needs to be corrected. It appears to only accept 2 answers as correct and is marking the question wrong if you enter the 255.255.254.0 mask as a third solution. Please correct as there is no current way to get this question correct.

By: Anonymous

Anonymous — Fri, 23 May 2014 21:20:45 +0000

They’re both in the same subnet with a network WIDE mask of 255.255.254.0. Therefore L2, no gateway required.

By: Anonymous

Anonymous — Thu, 22 May 2014 13:53:48 +0000

I don’t understand Q2. Is it E correct? With a network WIDE mask of 255.255.254.0, each interface does require an IP address. plz someone explain…

By: Anonymous

Anonymous — Tue, 20 May 2014 08:15:21 +0000

download free dumps from

wurl.cc/52R

By: Iceberg

Iceberg — Mon, 07 Apr 2014 08:42:37 +0000

Vlan10:
net 192.168.1.64/28
broadcast 192.168.1.95/28
Fa0/1.10 192.168.1.78 255.255.255.224

Vlan 20 :
net 192.168.1.128/26
broadcast 192.168.1.191/26

hostA: A: 192.168.1.79
C: Default gateway 192.168.1.78

hostB: F: IP address 192.168.1.190

By: Iceberg

Iceberg — Mon, 07 Apr 2014 08:42:02 +0000

No B ; D are the network address

By: ana

ana — Wed, 02 Apr 2014 00:15:17 +0000

hi. anyone resolved question 10 please? thursday i have my ccna exam.

By: !!!

!!! — Mon, 24 Mar 2014 09:38:50 +0000

i’m thinking q10 answers are B,C,D

By: Al7

Al7 — Wed, 12 Mar 2014 12:44:06 +0000

I cleared 200-120
Question 2 & 6 in today’s exam
Almost all questions from 9tut
Thanks everyone :)

By: Sabry

Sabry — Wed, 29 Jan 2014 18:21:32 +0000

Q1 was in today’s exam.

By: Abdullah

Abdullah — Fri, 17 Jan 2014 20:39:40 +0000

Hi, can anyone ps email me info on how to get the latest VCE 3.4.2 crack version or the version that can open recent dumps.
My email address is: mehdi01912330796@gmail.com
Thanks.

By: Anonymous

Anonymous — Tue, 31 Dec 2013 11:00:36 +0000

download free latest dumps from

9tut.webs,com

(replace comma with dot)

By: Wathnix

Wathnix — Sun, 29 Dec 2013 01:41:08 +0000

Aman,

Answer A is correct because host A is attached to switch port 6, which is in VLAN 10. In the router config, VLAN 10 has been assigned an IP address of 192.168.1.78 with a subnet mask of 255.255.255.224, which means that this subnet starts at 192.168.1.64 and ends at 192.168.1.95, therefore a host can be assigned any address between 192.168.1.65 and 192.168.1.94, answer A is within this range and has not already been assigned to something else.

Answer E is wrong because host B is attached to switchport 9, which is in VLAN 20. The router config shows that VLAN 20 has been assigned an IP address of 192.168.1.130 and therefore that address becomes the default-gateway for all hosts in VLAN 20. Host B should be configured with a default gateway of 192.168.1.130, not 192.168.1.129

By: Aman

Aman — Thu, 19 Dec 2013 16:01:10 +0000

please can anyone help me question 10 why the answers are A, C and F. why is not C, E AND F

By: Gert

Gert — Wed, 18 Dec 2013 17:44:07 +0000

@9tut: Question 2 in the quiz only expect 2 answers, but 3 are correct.

By: biacosta

biacosta — Thu, 28 Nov 2013 04:11:02 +0000

I PASSED yesterday, thanks to 9tut…..got a 920……woooohhoooo, study up!!!!

By: bbgunthai

bbgunthai — Sat, 23 Nov 2013 05:39:05 +0000

good

By: Anonymous

Anonymous — Mon, 28 Oct 2013 05:42:04 +0000

download latest dumps from
9
t
u
t
.
c
o
m
x
a
.
c
o
m