CCNA – Drag and Drop 2
Here you will find answers to CCNA Drag and Drop Questions – Part 2
Question 1
The left describes OSI layers, while the right provides some terms. Drag the items on the right to the proper locations.
Answer:
Network Layer:
1) IP addresses
2) packets
3) routing
Transport Layer:
1) windowing
2) UDP
3) segments
Question 2
The above describes some categories, while the below provides their corresponding router output lines. Drag the above items to the proper locations.
Answer:
1) Port operational: Serial0/1 is up, line protocol is up
2) Layer 2 problem: Serial0/1 is up, line protocol is down
3) Layer 1 problem: Serial0/1 is down, line protocol is down
4) Port disabled: Serial0/1 is administrator down, line protocol is down
Explanation:
A simple way to find out which layer is having problem is to remember this rule: “the first statement is for Layer 1, the last statement is for Layer 2 and if Layer 1 is down then surely Layer 2 will be down too”, so you have to check Layer 1 before checking Layer 2. For example, from the output “Serial0/1 is up, line protocol is down” we know that it is a layer 2 problem because the first statement (Serial0/1 is up) is good while the last statement (line protocol is down) is bad. For the statement “Serial0/1 is down, line protocol is down”, both layers are down so the problem belongs to Layer 1.
There is only one special case with the statement “…. is administrator down, line protocol is down”. In this case, we know that the port is currently disabled and shut down by the administrators.
Question 3
A user is unable to connect to the Internet. Based on the layered approach to troubleshooting and beginning with the lowest layer. Follow the guide and drag the contents to relevant modules.
Answer:
1) Verify Ethernet cable connection: Step 1
2) Verify NIC operation: Step 2
3) Verify IP configuration: Step 3
4) Verify URL: Step 4
Explanation:
The question asks us to “begin with the lowest layer” so we have to begin with Layer 1: verify physical connection; in this case an Ethernet cable connection. For your information, “verify Ethernet cable connection” means that we check if the type of connection (crossover, straight-through, rollover…) is correct, the RJ45 headers are plugged in, the signal on the cable is acceptable…
Next we “verify NIC operation”. We do this by simply making a ping to the loopback interface 127.0.0.1. If it works then the NIC card (layer 1,2) and TCP/IP stack (layer 3) are working properly.
Verify IP configuration belongs to layer 3. For example, checking if the IP can be assignable for host, the PC’s IP is in the same network with the gateway…
Verifying the URL by typing in your browser some popular websites like google.com, microsoft.com to assure that the far end server is not down (it sometimes make we think we can’t access to the Internet). We are using a URL so this step belongs to layer 7 of the OSI model.
Question 4
The left describes the types of cables, while the right describes the purposes of the cables. Drag the items on the left to the proper locations. (Not all items can be used).
Answer:
1) straight-through: switch access port to router
2) crossover: switch to switch
3) rollover: PC COM port to switch
Explanation:
To remember which type of cable you should use, follow these tips:
- To connect two serial interfaces of 2 routers we use serial cable
– To specify when we use crossover cable or straight-through cable, we should remember:
Group 1: Router, Host, Server
Group 2: Hub, Switch
One device in group 1 + One device in group 2: use straight-through cable
Two devices in the same group: use crossover cable
For example: we use straight-through cable to connect switch to router, switch to host, hub to host, hub to server… and we use crossover cable to connect switch to switch, switch to hub, router to router, host to host… )
Question 5
The left describes the types of switch ports, while the right describes the features. Drag the options on the right to the proper locations.
Answer:
Access Port:
- Carries traffic for a single VLAN
– Uses a straight-through cable to connect a device
– Connects an end-user workstation to a switch
Trunk Port:
- Carries traffic for a multiple VLAN
– Uses 802.1q to identify traffic from different VLANs
– Facilitates interVLAN communications when connected to a Layer 3 device
Question 6
The above describes the Spanning-Tree Protocol port states, while the below describes their functions. Drag the above items to the proper locations.
Answer:
- Learning: populating the MAC address table but not forwarding data frames
– Forwarding: sending and receiving data frames
– Listening: preparing to forward data frames without populating the MAC address table
– Blocking: preventing the use of looped paths
@Sopros
http://www.examcollection.com/cisco/Cisco.ActualTests.640-802.v2012-07-15.by.Sekhar.697q.vce.file.html
@ ALL
pls help notice Q2 administratively down is it a layer 2 or 3 problem ???
@ Anonymous
pls can u send a vce suite to me bcos the one I load from the net always ask for key
dantechglobal13@yahoo.com
DID IT!!…907…thx 9tut!!!!..CCNA certified….tons of questions from this site…read from top to bottom every question, because you will not know what pops up…q1, 3, and 4 on exam….good luck to all…can’t stress enough…read EVERY question on this site…
i love you 9tut mwaaah
@9tut and @All
Is it necessary to maintain sequence for drag and drop.
In dumps when i practice and arrange correct answer but not in sequence loose points.
Any comments please.
I am taking exam on next week.
Like question 1 from drag and drop.
Is it necessary to maintain sequence or just drag the right answer and drop into the box???
Please reply bcoz i will take exam on next week.
exam in dec.latest dumps pliiiiiz
justusnyaga@gmail.com
passed ccna exam this morning, thanks 9tut, question 2 and 3 came out of the exam.
hi ,latest dumps ccna exams ,
hani_2012_rad@yahoo.com
my exams after 3 days
9tut, the answer for Q3 given above is not supported for the answer given in number 5 composite quiz. Could you please look into this?
@Jamerican: I don’t understand. What do you mean? Is there something wrong in the composite quiz?
@jamerican
everything was perfect.i think u consider the target also..
Thank you 9tut, almost all the questions are from this site including simulations.
AFAIC that’s the best aswner so far!
TY 9tut.
Today I have passed the CCNA. (860/825)
50 questions 3 labs (VTP, EIGRP, ACL). 35 from 9tut.
Also thanks a lot Brar and Sekhar (still valid from examcollection)
Ty again 9tut
from here Q 2, 3
taking the exam on saturday 29th at 2pm gonna ace it
ccnajacob administratively down is not layer 2 o 3 problem, just the network administrator disable the interface, Q5 and Q6 on the exam.
i meant disabled it
hello can anyone provide me the latest ccna dumps,i shall be very thankful to you
rock3400@gmail.com
Valid Que :D
Q:1
Q:3
Q:4
5q. is it right…. or wrong….
because in prepking when i write this ans it will shows wrong…… which ans i fallow 9tut.com or prepking plz sugest me its urgent tommorow is my exam….. at 10:30am
@sangamesh swamy
Its Right .. :D
Trust 9tut :-)
Great amazing issues here. I am very glad to peer your article. Thank you so much and i’m having a look ahead to contact you. Will you please drop me a e-mail? NBA snapback hats http://cheapnbasnapbacks.simplesite.com/
Passed CCNA, questions 2 and 3 from here.
Q 2 and 3 were in my exam
also q 2 and 3 in my exam
Please send me the latest dump bekim.hajdini@gmail.com Thank you so much.
Please send me the latest dump at boubachezkamdem@yahoo.fr
Thank you so much
Q3 and Q4 on todays’s exam
hey guys, thank for the great info. banned from google in china-14 http://ckieo.takis.cn/viewthread.php?tid=1225444&extra=
Where the rooster crows there is a village. Schambala proverb what primer and paint should i used for a solid-27 http://11.nx.3694.cn/home/space.php?uid=4188&do=blog&id=130971
Q1, 2, 3 and 4 all valid
Hi all,
just as reference, since I revise for CCNA, Wireless access point also belong to the Group 1: Router, Host, Server
Good luck to every one that has ti give exams
Pliz i will sit for the exam next month, can someone send me the latest dumps on email: olesimbe@yahoo.com
Q1 & Q5 came to my exam today.
Read carefully all questions – it is worth getting premiere membership
VTP, EIGRP, & ACL2 are still valid.
q1 q3 q4 in exam today
Im questioning the drag and drops, too… they are in the right area, but not in the same order and vce test counted it wrong, but it was actually right… does it HAVE to be the way the test wants it? If so, that will suck and isnt really fair… If its right = its right no matter how they are lined up in that section. ie – access and trunk port #5 – i have them all right, but not in the order the test wanted and it counted it wrong… please advise…
thanks!
q3 in todays exam
I passed my exam and Had questions 1,3 and 4 in my exam.. 9tut 100%
When you do the exam, when you have drag and drop ,Do you have to put the answer in the same order that show here? Or Doesn’t matter de place?
Question 3 was on the CCNA test that I took today!
For Q5
When it says access ports use straight through cables, its also valid for trunk ports when switch connects to a router for inter-vlan communication.
Hello Guys I hope you will be fine there. I have CCNA (640-802) and CCNA security (640-554) Vouchers on special discount of 58% for World wide, with six months expiry date till you purchase. Each voucher cost 70USD.
Details Required For CCNA Voucher For Discount Processing:
1-Full Name. 1st Name & Last Name (as you want to appear on certificate & documents)
2-Country.
3-City.
4-State.
5-Pin Code (or Area Code)
6-Residential Address (or where you can collect your Certificate or further correspondence
can be received)
7-Date of birth
Add me on Skype through this information which is written below:
Skype Name: rockon660
you can also email me at this email address which is written below:
madeelqaiser@gmail.com
If you have any Questions feel free to contact me.
Thanks,
Best regards,
Adeel
Q1 and Q5, need to be arranged(Drag and drop to the appropriate place) the answer some order or can we select it randomly. please comment
Thanks 9tut. I made it. I passed my CCNA 200-120 today. The sim is Access-list 1 , Access-list 2 & EIGRP. A lot of new questions like Netflow, Syslog, SNMP, VRRP, and GLBP.
@ chanaka the order is *not* important. The question just wants to know when you use access port or trunk port. Hint access port connecting to a HOST.
I spoke too soon about the order. I am not sure.
Ethernet Cables the Simplest Way:
1. Switches are more evolved hubs. Switches and hubs belong to category 1
2. Servers are computers. Cisco routers are computers. Computers, Servers and Routers belong to category 2.
2 Rules to remember:
1. connect same type of device: crossover cable
2. connect different devices: patch cable (or straight-through)
i have exam next week
kindly send me the latest dumps (vce files)
shah.ahamed05@gmail.com