Home > New CCNA – New Questions

New CCNA – New Questions

November 5th, 2013 Go to comments

Note: If you are not sure about EtherChannel, please read my EtherChannel tutorial.

Question 1

Etherchannel question: You are given sw1 and sw2. The output of show etherchannel summary and show interface fa0/1. What is the cause of the problem? in exhibit, switch a cable is 100mb/s speed and b is 10mb/s. If you can look very carefully, there is speed mismatched to cause that problem. I selected “speed mismatch”

Question 2

Q2 (Etherchannel Questions that goes like this)
Refer to the exhibit. Etherchannel has been configured on Switch1 as shown.

Switch1# conf t
Switch1(config)# interface range gigabitethernet 1/1
Switch1(config)# Channel-group 5 Mode “AUTO”
Switch1#
Switch1(config)# interface range gigabitethernet 1/2
Switch1(config)# Channel-group 5 Mode “AUTO”

Which is the correct command set to configure etherchannel on Switch2?

A.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode auto

B.
Switch2# configure terminal
Switch2(config)# interface range gigabitethemet3/1 -2
Switch2(config-if)# channel-group 5 mode passive

C.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode desirable

D.
Switch2# configure terminal
Switch2(config)# interface range gigabitethernet3/1 -2
Switch2(config-if)# channel-group 5 mode ACTIVE

 

Answer: C

Good resource: http://www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/release/12.1_13_ea1/configuration/guide/swethchl.html#wp1028480

Question 3

Which OSPF command turn OSPF on all interfaces of a router?

Answer: network 0.0.0.0 255.255.255.255

Question 4

Network admin creates a layer 3 Etherchannel, bounding 4 interfaces into channel group 1. On what interface is the IP address configured?

A. the port-channel 1 interface

B. the highest number member interface

C. all member interfaces

D. the lowest number member interface

 

Answer: A

Question 5

3. What is the authentication type of SNMPv2?

A. Community Strings
B. HMAC-MD5
C. HDMAC-SHA

Answer: Community string

Question 6

What parameters can be different on ports with an Etherchannel?

A. speed
B. trunk encapsulation
C. DTP negotiation setting
D. duplex

 

Answer: C

Comments (908) Comments
Comment pages
1 2 3 4 19 1994
  1. Anonymous
    December 25th, 2013

    Guys i just PASSSED
    This website has helped me alot.i have the latest dumps with me.mail me to get them at stuckatvpn@hotmail.com

  2. Hogr
    December 26th, 2013

    please some one can help me to send new dump ccna ise_it@yahoo.com

  3. Digital Mafia
    December 26th, 2013

    Just passes in the afternoon. 972/1000. This site is greate. got EIGRP, ACP simlet and access list simulations. Got 1 ether channel question and answer was speed mismatch. few questions on HSRP, GLBP net flow and SNMP. go through jeremy’s nuggets and this site. All the best

  4. HALFPINT
    December 27th, 2013

    can someone please send the latest dump, I’ll be taking my test soon! bfordjr84@gmail.com

  5. Anonymous
    December 28th, 2013

    Yes you can get download from video and updated dump from
    e
    x
    a
    m
    d
    u
    m
    p
    @
    .
    n
    e
    t

  6. Anonymous
    December 30th, 2013

    Passed My Exam Guys…
    Thanks to the latest dumps.click the link if you want to have those dumps
    www . chrst . ph/1hh

  7. jrod
    December 30th, 2013

    is 9tut icnd1 is down

  8. saeed
    December 30th, 2013

    http://www.digitaltut.com/ it is not working, anyone can tell me what is the problem why does it not work?

  9. Don
    December 30th, 2013

    Help! The website for CCNP ROUTE (www.digitaltut.com) is unreachable. Is it going to come back up?

  10. Anonymous
    December 31st, 2013

    download free latest dumps from
    9
    t
    u
    t
    .
    w
    e
    b
    s
    .
    c
    o
    m

  11. Amrutha
    January 1st, 2014

    CCNP ROUTE link is not reachable.
    Any idea when will it be up?

  12. Anonymous
    January 1st, 2014

    Hi everyone
    Please ,send me latest CCNA (200-120) dumps.
    mh.abbasi@live.com

  13. Anonymous
    January 2nd, 2014

    download latest dumps from
    9
    t
    u
    t
    .
    w
    e
    b
    s
    .
    c
    o
    m

  14. Gihan Chandima
    January 3rd, 2014

    Passed the CCNA 200-120 with a score of 972/1000
    thkx to ACME EXAMTUT and Specially 9tut. i got 99% of the questions from theses dumps but don’t simply learn them by heart, try to understand the answers coz even though the real exam will be similar, there will be many traps.
    Good Luck to all

  15. poili
    January 3rd, 2014

    i CLEARED THE CCNA (200-120) LAST WEEK THE EXAM IS EASY YOU
    WANT TO DO SOME HARD WORK IS USE STUDY MATERIAL FROM
    video material and sum updated material hear
    e
    x
    a
    m
    d
    u
    m
    p
    .
    n
    e
    t

  16. help
    January 4th, 2014

    please help. This will be my second time trying to pass the exam. Please send me the latest dumps. I am desperate. My e-mail is vmarti01@grandecom.net

  17. Contra
    January 4th, 2014

    @POILI
    you scammer..you dont even know how to speak english and you want us to follow your scam website???

  18. Ed
    January 4th, 2014

    I have the LATEST AND MOST UPDATED dumps.mail me to get them at stuckatvpn@hotmail.com

  19. Ebai Richard
    January 4th, 2014

    Happy new year every one. please i need the latest CCNA dumps kindly send to ebairichard@gmail.com

  20. YESSS!
    January 5th, 2014

    I passed CCNA 803 today with an 876. Labs were EIGRP, ACL, ACL Simlet. Good Luck guys!

  21. tech_gurl from Canada
    January 5th, 2014

    Passed my CCNA exam today (Jan 5th) with 920, Got 1 drag and drop with cost, load, delay, option and got ACL, ACL2 and EIGRP sims. There was 1 new question on where the cisco router loads they OS that I don’t remember. You will still need to understand the concepts for some VLAN and switch questions. Study the examtut.279 dump along with the new questions posted on the Z404.29q dump

    These are the new questions that I remember from my exam: –

    Question 8
    What is the alert message generated by SNMP agents called ?

    A. TRAP
    B. INFORM
    C. GET
    D. SET

    Answer: a,b

    Question 16
    What are three benefits of GLBP? (Choose three.)

    A. GLBP supports up to eight virtual forwarders per GLBP group.
    B. GLBP supports clear text and MD5 password authentication

    between GLBP group members.
    C. GLBP is an open source standardized protocol that can be

    used with multiple vendors.
    D. GLBP supports up to 1024 virtual routers.
    E. GLBP can load share traffic across a maximum of four

    routers.
    F. GLBP elects two AVGs and two standby AVGs for

    redundancy.

    Answer : B, D, E

    Question 20
    What is the default Syslog facility level?

    A. local4
    B. local5
    C. local6
    D. local7

    Answer: D

    Question 24
    What Netflow component can be applied to an interface to

    track IPv4 traffic?

    A. flow monitor
    B. flow record
    C. flow sampler
    D. flow exporter

    Question 28
    What are three factors a network administrator must consider

    before implementing Netflow in the network? (Choose three.)

    A. CPU utilization
    B. where Netflow data will be sent
    C. number of devices exporting Netflow data
    D. port availability
    E. SNMP version
    F. WAN encapsulation

    Answer: A, B, C

    Question 29
    What are two enhancements that OSPFv3 supports over

    OSPFv2? (Choose two.)

    A. It requires the use of ARP.
    B. It can support multiple IPv6 subnets on a single link.
    C. It supports up to 2 instances of OSPFv3 over a common link.
    D. It routes over links rather than over networks.

    Refer to the exhibit. Etherchannel has been configured on

    Switch1 as shown.

    Switch1# conf t
    Switch1(config)# interface range gigabitethernet 1/1
    Switch1(config)# Channel-group 5 Mode “AUTO”
    Switch1#
    Switch1(config)# interface range gigabitethernet 1/2
    Switch1(config)# Channel-group 5 Mode “AUTO”

    Which is the correct command set to configure etherchannel

    on Switch2?

    A.
    Switch2# configure terminal
    Switch2(config)# interface range gigabitethernet3/1 -2
    Switch2(config-if)# channel-group 5 mode auto

    B.
    Switch2# configure terminal
    Switch2(config)# interface range gigabitethemet3/1 -2
    Switch2(config-if)# channel-group 5 mode passive

    C.
    Switch2# configure terminal
    Switch2(config)# interface range gigabitethernet3/1 -2
    Switch2(config-if)# channel-group 5 mode desirable

    D.
    Switch2# configure terminal
    Switch2(config)# interface range gigabitethernet3/1 -2
    Switch2(config-if)# channel-group 5 mode ACTIVE

    Question

    Refer to the exhibit. An administrator pings the default

    gateway at 10.10.10.1 and sees the output as

    shown. At which OSI layer is the problem?

    C:\> ping 10.10.10.1

    Pinging 10.10.10.1 with 32 bytes of data:

    Request timed out.

    Request timed out.

    Request timed out.

    Request timed out.

    Ping statistics for 10.10.10.1:

    Packets: sent – 4, Received = 0, Lost – 4 (100% loss)

    A. data link layer

    B. application layer

    C. access layer

    D. session layer

    E. network layer

  22. Sneha
    January 6th, 2014

    Passed exam with 945/1000 today .
    100% valid dumps : http://www.examcollection.com/cisco/Cisco.Actualtests.200-120.v2013-12-10.by.Watson.314q.vce.file.html#comment .

    sims which i got : ACL1 , ACL2 , EIGRP . Same as here .

    Thanks to 9tut.

  23. Anonymous
    January 6th, 2014

    download free latest dumps from
    9
    t
    u
    t
    .
    w
    e
    b
    s
    .
    c
    o
    m

  24. Anonymous
    January 6th, 2014

    Can someone please send new dumps to brianvangenderen@yahoo.com. i did not do so hot today looking at the older questions

  25. A-Jay
    January 7th, 2014

    Guy i passed my exams…………………………………

    thanks to 9 tut and i also have the most updated and latest dumps.mail me to get them at stuckatvpn@hotmail.com

  26. Mohsin
    January 7th, 2014

    Just passed my CCNA exam today with 903 marks thanks 9tut

  27. Anonymous
    January 7th, 2014

    Please sent me the latest dump felmonz@gmail.com i really want to review the recent dump before my exam date.

  28. Mohammad Enayet Karim
    January 8th, 2014

    Hi please tell me are all questions are coming from new ccna questions from 9tut? Do I have to solved the old ccna questions also.

  29. Thea Beltran
    January 9th, 2014

    Please 9tut do send me the latest dump so that I can start reviewing for my test. beltrananthea@yahoo.com

    Thanks! :)

  30. Folorunso
    January 9th, 2014

    Please send me latest ccna questions at christianharoun@gmail.com for practice for my exams

  31. Pashy
    January 9th, 2014

    Hi guys, I am thinking of starting a CCNA programe, i live in Columbia MD, any recomendation on the institute. Thanks pashy4@hotmail.com

  32. JeffA
    January 10th, 2014

    Using 9tut is pretty awesome, but in an effort to really learn some of this too so I am not a paper CCNA, the site http://www.freeccnastudyguide.com is a free resource that covered all the exam topics and has actual labs on them that you can do too.

  33. Jay J
    January 10th, 2014

    Guys I am Scheduled to take the CCNA next month.. PLease send me the latest 200-102 Exam questions you May have Jedi84luke@yahoo.com

  34. freddy
    January 11th, 2014

    Please send me the latest dump at freddyliaw91@outlook.com

  35. Anonymous
    January 13th, 2014

    Please can someone send me the latest dumb questions topojons@yahoo.com

  36. goran
    January 14th, 2014

    i just passed the ccna 200-120 14/1/2014 two hours ago with full mark 1000/1000 its easy i used waston 314q and 278 examtut and 9tut and examtut the questions are easy my sim is eigrp and ACL and ACL2 just small modification.

  37. Anonymous
    January 14th, 2014

    best option to download latest dumps
    9tut.webs,com

  38. taider
    January 15th, 2014

    tommrow my exam help plz???!!!!!!

  39. Ngembe
    January 15th, 2014

    Can somebody please assist, am trying to open VCE files.send to hmahaso2014@gmail.com

  40. Aocamacho
    January 15th, 2014

    I passed my exam CCNA today, score 986/1000, 100% valid. Labs ACL1 , eIGRP , ACL 2 the same the 9tut little changes of the labs, very very very easy, One new question from etherchannel.. Studied the http://www.examtut.com/2013/09/new-questions-in-ccna-200-120-hsrp-vrrp.html
    and also two questions from New CCNA – New Questions 2 the 9tut.
    URLS
    Cisco.Actualtests.200-120.CCNA.v2013-10-01.by.examtut.278q.vce and Cisco.Test-inside.200-120.v2013-11-28.by.E-Z404.29q.vce,
    Labs the http://www.examtut.com/search/label/CCNA%20Simulation and 9tut the same questions,
    I Practice 60 question 1 to 60 every time, so 61 to 120, 121 to 180, 181 to 240 to finish, to avoid mistakes, the lab de same practice and practice, try to understand the questions.

  41. Anonymous
    January 15th, 2014

    Passed today…… Glory

  42. Anonymous
    January 16th, 2014

    download free latest dumps from
    9
    t
    u
    t
    .
    w
    e
    b
    s
    .
    c
    o
    m

  43. FARRUKH
    January 16th, 2014

    Hi
    someone guide me for the EXAM of New CCNA 200-120
    farrukh_2980@yahoo.com
    Thanks

  44. taider
    January 16th, 2014

    thanks alot 9tut i passed with 1000 degree thank u alot
    acl1 acl2 eigrp simulations
    for everyone u have to study from 9tut and examtut and examcollection 314&278&319 dumps

  45. ccna20jan
    January 16th, 2014

    do not waste time sending an email to stuckatvpn@hotmail.com

  46. Eng.Mohamed
    January 17th, 2014

    looking for VCE 3.4.2 with activation —– IMPORTANT Please — my mail is : mohamed.cse.asu@hotmail.com

  47. HackSpeed
    January 17th, 2014

    me too looking for VCE 3.4.2 with activation! My mail is : txus_morte@hotmail.com

  48. Abdullah
    January 17th, 2014

    Hi, can anyone ps email me info on how to get the latest VCE 3.4.2 crack version or the version that can open recent dumps.
    My email address is: mehdi01912330796@gmail.com
    Thanks.

  49. Rashmi
    January 19th, 2014

    Hi, can anyone mail me the latest CCNA 200-120 dumps plz..
    id: rashmi.2689@gmail.com

  50. Anonymous
    January 20th, 2014

    Hi all, just passed 957 in Milan Italy
    The questions were all there.

    Be careful with the SNMP question. It is not as straight forward as inform/trap.
    It asks the difference between the three versions.
    Anyway, this site was great

    Good luck to y’all

Comment pages
1 2 3 4 19 1994
Add a Comment