CCNA – Hotspot
Here you will find answers to CCNA hotspot Questions
Hotspot Routing Question
Question 1:
If the router R1 has a packet with a destination address 192.168.1.255, what describes the operation of the network?
A – R1 will forward the packet out all interfaces
B – R1 will drop this packet because it is not a valid IP address
C – As R1 forwards the frame containing this packet, Sw-A will add 192.168.1.255 to its MAC table
D – R1 will encapsulate the packet in a frame with a destination MAC address of FF-FF-FF-FF-FF-FF
E – As R1 forwards the frame containing this packet, Sw-A will forward it ti the device assigned the IP address of 192.168.1.255
Answer: B
Question 2:
Users on the 192.168.1.0/24 network must access files located on the Server 1. What route could be configured on router R1 for file requests to reach the server?
A – ip route 0.0.0.0 0.0.0.0 s0/0/0
B – ip route 0.0.0.0 0.0.0.0 209.165.200.226
C – ip route 209.165.200.0 255.255.255.0 192.168.1.250
D – ip route 192.168.1.0 255.255.255.0 209.165.100.250
Answer: A
Quetion 3:
When a packet is sent from Host 1 to Server 1, in how many different frames will the packet be encapsulated as it is sent across the internetwork?
A – 0
B – 1
C – 2
D – 3
E – 4
Answer: C or D(depending on your understand, please read the comments to understand why)
Question 4:
What must be configured on the network in order for users on the Internet to view web pages located on Web Server 2?
A – On router R2,configure a default static route to the 192.168.1.0 network
B – On router r2, configure DNS to resolve the URL assigned to Web Server 2 to the 192.168.1.10 address
C – On router R1, configure NAT to translate an address on the 209.165.100.0/24 network to 192.168.1.10
D – On router R1, configure DHCP to assign a registered IP address on the 209.165.100.0/24 network to Web Server 2
Answer: C
Question 5:
The router address 192.168.1.250 is the default gateway for both the Web Server 2 and Host 1. What is the correct subnet mask for this network?
A – 255.255.255.0
B – 255.255.255.192
C – 255.255.255.250
D – 255.255.255.252
Answer: A
Hotspot Frame-relay Question
(In the old days, this question was a multi-choice question but Cisco upgraded it into a lab-sim question. Therefore, instead of listing all the configuration as above, you have to type show frame-relay map and show running-config to get its configuration)
Note: If you are not sure about Frame-Relay, please read my Frame Relay tutorial.
Question 1:
What destination Layer 2 address will be used in the frame header containing a packet for host 172.30.0.4?
A – 704
B – 196
C – 702
D – 344
Answer: C
Question 2:
A static map to the S-AMER location is required. Which command should be used to create this map?
A – frame-relay map ip 172.30.0.3 704 broadcast
B – frame-relay map ip 172.30.0.3 196 broadcast
C – frame-relay map ip 172.30.0.3 702 broadcast
D – frame-relay map ip 172.30.0.3 344 broadcast
Answer: B
Question 3:
Which connection uses the default encapsulation for serial interfaces on Cisco routers?
A – The serial connection to the MidEast branch office
B – The serial connection to the DeepSouth branch office
C – The serial connection to the NorthCentral branch office
D – The serial connection to the Multinational Core
Answer: A
Question 4:
If required, what password should be configured on the router in the MidEast branch office to allow a connection to be established with the Dubai router?
A – No password is required
B – Enable
C – Scr
D – Telnet
E – Console
Answer: A or D (because maybe there are 2 versions of this question, depending on the output of “show running-config” command, please read the explanation below)
Explanation
This question is not clear for a long time but now maybe the trick was solved. What Cisco wants to ask is the word used as password, not the type of connection, so in the exam you might see some strange words for answers like “En8ble”, “T1net”, “C0nsole”. All you have to do is to use the command “show running-config” as wx4 mentioned below to find the answer.
wx4 commented:
Q4: if password required which?
in my example it was connection to North!
How to figure out which pw is required?
#show running-config
1. check the interface to the router you need connection to. If there is “ppp authentication” you need a password!
2. you will find the password on the top of your running-config output
check the area:
username North password c0nsole
username xxxxx yyyyy
username…
in my case it was c0nsole, in your case it can be no password needed or a different password.
If you are still not clear, please read anton‘s comment:
A big question I noticed here was about the FR Lab regarding the password. You have to perform a show running-config and look for USERNAME and PASSWORD.
i.e.
username South_Router password c0nsol3
username North_Router password t31net
Obviously this has to be en PPP encapsulation, if asked for a posible password for SOUTH_ROUTER you pick c0nsol3, and for NORTH_ROUTER you pick t31net. If you’re running HDLC, i would pick “no password is required”.
@Dr.Arubix
To answer this question you need to check the config of Dubai router using ‘show run’ command and see for a line like :
username MidEast password xxxx
if you see above line and in place of xxxx one of the words besides B, C, D or E you should choose that answer. If no such line present in the running config of Dubai router then No password is required.
Aalhamdulillah,
Hi Everyone,
I M Just here to say thank u so much to 9tut and all who post there valuable comment on this website.
I took mah Exm on 4th Feb’11 and I hv pass d Exm with scoring 923.
All d best to u all who is gonna be appeare dr exm.
@ SG
Right on man. Thanks so much!
hi
can any expnlain me pls that is this simulation question in exam like rest of eigrp, RIP, NAT OR these are just multiple questions.
pls am new in netwrok program, and i was given a assigment on the diffrent types of cables and i should cartigores the rate ecah cable transmite
what shlou ido
In frame relay question 4, my answer is A (no password is required) … because base on the running-config of Dubai router, s1/1 is configured for default encapsulation which is HDLC, and does not need a password to authenticate or established connectivity…
If there is a PPP there, yes the password depends on the router config…
@ abdul
Correct answer is “c” 10.1.3.3
I think you are forgetting the KISS principle: Routers do not forward broadcasts.
At least not by default. Directed broadcasts and ip helper address are beyond the scope of the CCNA (at least according to my understanding).
hi
can anybody tell me the fee of ccna exam?????
http://quest4.org/ccna/
For the Hot Spot Frame Relay Question:
If: the answer to Q3 is “MidEast”, we are saying it is using HDLC to connect to Dubia,
Then: the answer to Q4 has to be “No Password Required”, because we just said it was an HDLC connection.
@anonymous $250
Hi 9 tut and users…
Q4. Explicitly stipulates ‘configured’ in the question. When one telnets to another device, one does not configure a password, hence option A is correct. A password should be configured only if the serial connection uses authentication, such as in PPP : PAP or CHAP.
I think this should resolve the ambiguity of the question.
if one host want 2 send data 2 another host in diff network what it wiil do?
1.arp
2.send 2 default address
n dumbz answer is 1
Q4:he asked about if MIDs want to connecttion with dubai ,it will need password make telnet on dubai so A is the answer
Aalhamdulillah,
Hi Everyone,
I M Just here to say thank u so much to 9tut and all who post there valuable comment on this website.
I took mah Exm on 29th March’11 and I hv pass d Exm .
All d best to u all who is gonna be appeare dr exm.
Glory honour and power to our good God,
Hi Everyone,
I M Just here to say thank u so much to 9tut and all who post there valuable comment on this website.
I took mah Exm on 4th Feb’11 and I hv pass d Exm with scoring 923.
All d best to u all who is gonna be appeare dr exm.
Hello people, I just take the exam and this question took my exam, but the scenario was NOT available option to show frame-relay map and thus could not verify what was the DLCI.
Absurd that in a certification exam.
I was approved, most do not believe that my score was marred by an error of the director of the race.
The show frame-relay works just fine…fyi
We can’t cook-book life, and certainly not Cisco Exams….Trust me, they are tough!
Sorry bout lengthy post in-advance…will be worth-it….
[Q#4 FRAME-SIM]
A – No password is required
B – Enable
C – Scr
D – Telnet
E – Console
For my own edification:
1st Step: Verify the Physical Connection to “MidEast” Branch office. Which is S1/1->(Ex).
2nd Step: Check Dubai!
Dubai# sh running-config!
!(omiited)
!
interface serial 1/1 (To MidEast RTR)
192.168.0.1 255.255.255.252
! (blanked=Default HDLC)
OR:
interface serial 1/1 (To MidEast RTR)
192.168.0.1 255.255.255.252
encapsulation ppp
ppp authentication chap
username Mideast password C0nsole
So if don’t see Encap under S1/1 on Dubai, then no password
if you see the *username Mideast password C0nsole*, then password is C0nsole!
GRAVY!!!!!
Thank you 9TUT Community, Love your stuff!
all these questions are on pass4sure. now who uses who’s information
These Dump companies certainly they feed from each other…Trying to make a $Buck, American Style….
Can someone verify my NO-Password Post Please>?:
A – No password is required
B – Enable
C – Scr
D – Telnet
E – Console
(See March 31st,2011.) Above, and tell me if it looks like 100%?
Thanks Team!
Hotspot Frame-relay Question 4
ANSWER IS SO OBVIUOS:
WE DO NOT CONFIGURE THE PASSWORD ON MIDEAST FOR ACCESS DUBAI ROUTER THROUGH VTY, IF YOU ALL FORGOT, WHEN WE ESTABLISH CONNECTION FROM MIDEAST TO DUBAI VIA TELNET (VTY) WE TYPE THE PASSWORD BY HAND!!!! WE DON’T CONFIGURE THIS PASSWORD ON MIDEAST!!!! THIS IS SO OBVIOUS!!! CORRECT THE ANSWER 9TUT!!!
IN THIS CERTAIN EXAMPLE ANSWER MUST BE A) NO PASSWORD IS REQUIRED
Hotspot Routing Question 3
ANSWER D
Sorry for my english (this is not my native language)
Hi guy,s i am going for CCNA tommorrow any suggestions and can some one tell me which subnet table i should write on board before starting the exam??
Admin, hello! here are having problems with your site. Write me. ECK 98956785664
can any one tell me the description of bellow question….
what destination layer 2 address will be used in the frame the host 172.30.0.4?
A) 767
B) 682
C) 455
D) 46
and the answer is 682 (kindly define briefly why this ans)
9tut is the best!
how do i get the questions on pass4sure!
Took ICND2 today. the Frame Relay question was on the exam. Hotspot was not.
hello guys
im preparing for my exam next week on the end of MAY.. i need all the help that u all can give me …and please can someone send me the latest dumps in nusaiba282@hotmail.com
Reading the question – If required What password should be configured – I think it is a remote connection between the devices and that should be telnet
Routing Q#1: assume that answer B is right. :(
The point is that we can’t really understand the question.
If an ICMP request (from ISP network – this cannot be done in real world because private addresses cannot be routed on the Internet) was received on R1 with broadcast ip address (192.168.1.255), R1 will reply with its s0/0/0 interface ip address (209.165.100.250) because it has route to the network (192.168.1.0) via directly connected route. (same in traceroute and don’t forward broadcast mac address out other interfaces!!)
If this ICMP request is from internal lan, it will become a broadcast ping and hosts in the network will reply by using their own ip addresses as source ip address in the packet. (as unicast reply)
For a TCP connection like http request, with this broadcast address, R1 itself is not a http server, so simply it drops the segment because the requested TCP port is not existed and it will send back RST+ACK to reset the connection. So i finally thought, lets consider B is the suitable answer that simply defined it is an invalid ip address.
Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely
reason that interface FastEthernet 0/10 is not the root port for VLAN 2?
https://lh6.googleusercontent.com/-w_Kfp5HVNQQ/TdsxSvO4xrI/AAAAAAAABOA/dVfjRzsGU6s/s576/stp.bmp
A. This switch has more than one interface connected to the root network segment in VLAN 2.
B. This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.
C. This switch interface has a higher path cost to the root bridge than another in the topology.
D. This switch has a lower bridge ID for VLAN 2 than the elected designated switch.
ans is ‘C’… how ? can any one explain..
Hi all
I will be taking my exams mid june and please provide latest dump question if you guys have….to Sean.rammutla@standardbank.co.za.
thanks
Can someone kindly send me the latest dumps for CCNA 802 exam to cts1234586@hotmail.com
Many Thanks
q3 c is corret
becuse farme is consider in router the senariyo two router are ther.
I think the answer in question number 4 is C…
Hi all ¡¡¡
In this hot spot you need to put the show commands or its not necesary?
The 2 hotspot questions are for the ccna exam?
Best regards.
HDLC does not support authentication –> It is not required for a connection to the Dubai Router from the MidEast. The VTY password is for telnetting.
Please explain the answer of Hotspot Routing Question 3. Why C could be the correct answer ? it should be D only.
Thanks!
Kapil Kumar
Which connection uses the default encapsulation for serial interfaces on Cisco routers?
Well Serial 1/1 the default encapsulation ‘For Serial Inerfaces’ is just that. No config. It must be a leased line with 2 IP’s each end.
Where as Serial 1/0 has got a configured encapsulation of Frame Relay presumably as no PPP is configured it is also running HDLC default.
So the question is almost a trick in that they want to know what is the default for ‘Serial interfaces’ not the default encapsulation for Frame Relay.
Hope that makes sense !
Can some tell me if i have to memorize the command or is tab working to complete the command?
Thanx for great info :)
Hi , I am doing CCNA exam in next 2 week , can someone help send me the last dumps to teseymur@azercell.com,please
Thank ,
for q1, why is the answer not d? Doesnt the router do this for a broadcast?
Or am I wrong
who has a definative answer for q3?
I think the question for Q1 should be, “if the router R1 receives a packet…” using “has” instead of “receives” adds confusion to the question.
the answer is B, since the router does not forward broadcasts.
Q3- answer is 3, the switch does not change the frame, it only reads the destination address and forwards itto the specific port that has the mac address.